Tag: manifold

Volvo S80 2.4T Thermatec Teflon Intake Spacer (PTFE)

Bought a Teflon (PTFE) intake spacer for the intake manifold from Thermatec. It will isolate the intake manifold from the warm engine, which will result in lower intake temperatures. The phenolic spacers are identical in function, only the material used is different.

Lowering the Intake Air Temperature (IAT), will result in higher power figures. A simple supporting mod, which is quite inexpensive.

Pro tip: make a small indentation in the top left corner of the spacer where the bolt would go through the spacer/gasket (where the thermostat housing is), this will make the installation a lot easier due to the restricted space in that area.

URL: www.ebay.nl/itm/302474396288

Volvo S80 2.4T Thermatec Phenolic Intake Spacer

Volvo S80 2.4T Thermatec Phenolic Intake Spacer

Volvo S80 2.4T Thermatec Phenolic Intake Spacer




Volvo S80 2.4T Japanifold Exhaust Manifold

When I wanted to mount the TD04HL-16T turbo, I also wanted to couple it with the Japanifold, that should give good performance, but also the distinctive rumble of the 5 cilinder engine. I scored one via internet for a good price. The quality is immaculate, as they can handle a lot of abuse before they even start cracking.

But in the end I sold it, because my 2.4T already had the Japanifold fitted, so happy days 🙂 !

They are made in Japan, hence the name “Japanifold”. Partnr: 9207688

Volvo S80 2.4T Japanifold

Volvo S80 2.4T Japanifold

Volvo S80 2.4T Japanifold

Volvo S80 2.4T Japanifold


Volvo S80 2.4T Project 16T Turbo

I had pretty big plans for the S80, shooting for a 270bhp instead of the 200bhp that the 2.4T has normally. You need an upgrade turbo for this, which I sourced from a T5 model, which has 250bhp bone stock. The swap would involve the TD04HL-13T to TD04HL-16T or 13T to 16T for short.

Fitment is pretty straightforward, but the coolant lines run differently, and this was quite a hassle as information on the internet seems very scarce. I found some, but needed some creativity as the build progressed.

I was also planning to mount the later “R” series manifold, but decided to sell it, as the Japanifold would give much better sound and equal performance.

In the end, I sold the 16T and mounted the 13T, saving the money up for something else. I needed to adjust the car a little bit, and according to the max MAF values, it makes about 240-245bhp, which is awesome.

It’s a totally different car from when I first bought it, that’s for sure!

Volvo S80 2.4t TD04HL-16T Turbo

Volvo S80 2.4t TD04HL-16T Turbo

The TD04HL-16T with the R-manifold

Volvo S80 2.4T TD04HL-16T + Upgrade Exhaust Manifold

The TD04HL-13T vs TD04HL-16T

Volvo S80 2.4T TD04HL-16T vs 13T turbo

Volvo S80 2.4T TD04HL-16T vs 13T turbo

Volvo S80 2.4T TD04HL-16T vs 13T turbo

Modifications needed for fitting the coolant lines

Volvo S80 2.4T Coolant Line Modification

Volvo S80 2.4T Coolant Line Modification

Rubbing will occur here

Volvo S80 2.4T Coolant Line Modification